Hallo zusammen,
ich beabsichtige für mein nächstes Projekt HITEC HV Servos HS7954SH sowie HS7950TH zu verbauen. Diese wollte ich direkt mit 2SLipo betreiben.
Bei einem Freund habe ich gesehen, daß es leider nicht funktioniert hat. Bei voll geladenen Akkus fangen die Servos um den Nullpunkt zu zittern an.
Laut einem Servicebulletin von Hitec liegt das an der hohen Spannungslage, obwohl die Servos eigentlich dafür gemacht sind.
Zur Abhilfe sollen folgende Maßnahmen ergriffen werden:
In some cases, when using the 7940/45/50's in applications that require a very long extension, they may randomly jump (glitch) when powered by 2S LiPo/Li-Ion batteries. Although this may occur with many systems, it is most commonly found when using JR/Spektrum type RX's, especially the Power Safe versions. We have discovered that due to the resistance in long extension wires, the signal voltage drops, thus causing the issue. We recommend that only high-quality, twisted, 22-guage, high strand count, gold connector extensions be used. In the event that this does not resolve the problem, there are a few options. The use of a signal line booster like that made by Spektrum, and soon to be available by Hitec, resolves the issue in almost all cases. Another option is to solder a .22 tantalum capacitor between +/- on the extension. These solutions are typically only needed when using Li-Po/Li-Ion batteries to lower the voltage below 7 volts and is not needed when using 5-cell NiCd/NiMH or LiFe batteries.
We are aware that these are high voltage servos designed to operate at the maximum voltage allowed for maximum performance. However, to accommodate some radio systems, steps may be required to assure the above issue will not occur. Hitec apologizes for any inconvenience this may cause and is working on a series of new Ultra Heavy Duty extensions (with and without boosters) that will resolve this issue.
Jetzt bin ich am überlegen LIFEPO4 Akkus direkt zu verwenden. Diese haben im voll geladenen Zustand (6,6Volt) eine deutlich niedrigere Spannung als Lipos. Damit sollte es eigentlich gehen. Bedenken habe ich allerdings wenn die Spannung im Laufe der Zeit abnimmt, also uner 6Volt sinkt. Die Betriebsspannung dieser Servos ist ja von 6 - 7,4 Volt angegeben.
Funktioneren die Servos dann noch? Hat dies schon mal jemand ausprobiert?
Frank
ich beabsichtige für mein nächstes Projekt HITEC HV Servos HS7954SH sowie HS7950TH zu verbauen. Diese wollte ich direkt mit 2SLipo betreiben.
Bei einem Freund habe ich gesehen, daß es leider nicht funktioniert hat. Bei voll geladenen Akkus fangen die Servos um den Nullpunkt zu zittern an.
Laut einem Servicebulletin von Hitec liegt das an der hohen Spannungslage, obwohl die Servos eigentlich dafür gemacht sind.
Zur Abhilfe sollen folgende Maßnahmen ergriffen werden:
In some cases, when using the 7940/45/50's in applications that require a very long extension, they may randomly jump (glitch) when powered by 2S LiPo/Li-Ion batteries. Although this may occur with many systems, it is most commonly found when using JR/Spektrum type RX's, especially the Power Safe versions. We have discovered that due to the resistance in long extension wires, the signal voltage drops, thus causing the issue. We recommend that only high-quality, twisted, 22-guage, high strand count, gold connector extensions be used. In the event that this does not resolve the problem, there are a few options. The use of a signal line booster like that made by Spektrum, and soon to be available by Hitec, resolves the issue in almost all cases. Another option is to solder a .22 tantalum capacitor between +/- on the extension. These solutions are typically only needed when using Li-Po/Li-Ion batteries to lower the voltage below 7 volts and is not needed when using 5-cell NiCd/NiMH or LiFe batteries.
We are aware that these are high voltage servos designed to operate at the maximum voltage allowed for maximum performance. However, to accommodate some radio systems, steps may be required to assure the above issue will not occur. Hitec apologizes for any inconvenience this may cause and is working on a series of new Ultra Heavy Duty extensions (with and without boosters) that will resolve this issue.
Jetzt bin ich am überlegen LIFEPO4 Akkus direkt zu verwenden. Diese haben im voll geladenen Zustand (6,6Volt) eine deutlich niedrigere Spannung als Lipos. Damit sollte es eigentlich gehen. Bedenken habe ich allerdings wenn die Spannung im Laufe der Zeit abnimmt, also uner 6Volt sinkt. Die Betriebsspannung dieser Servos ist ja von 6 - 7,4 Volt angegeben.
Funktioneren die Servos dann noch? Hat dies schon mal jemand ausprobiert?
Frank